A Bixpy trolling motor is a small electric outboard for kayaks, paddleboards and inflatables. The K-1 motor weighs 2.8 lb, runs off a separate 24V lithium pack, and attaches through one of Bixpy’s mounting adapters. Bixpy rates it at 33 lb of thrust with its PP-378 battery and 38 lb with the larger PP-768.
We don’t sell Bixpy motors, batteries or adapters. We sell graphs, live sonar and transducer mounts, and some of that gear suits small boats. The specs below come from Bixpy’s own site as we found it in October 2026, unless we say otherwise.
What Bixpy sells in October 2026
Bixpy splits its range into two series. The Adventure Series is built around the K-1 motor, which Bixpy describes as equivalent to 1 hp. The Freedom Series is the N-3, a 3 hp equivalent tiller outboard for small boats. Bixpy calls both of them outboards. On a kayak, the K-1 does the job most people would hand to a small trolling motor.
Prices here are list prices on Bixpy’s site in October 2026. Many kits and adapters showed as sold out when we checked, so confirm stock before you plan a season around one.
The K-1 kits
- K-1 Outboard Kit ($1,399): the K-1 motor, a PP-378 power pack, a Bluetooth remote, a magnetic kill switch on a floating leash, and a 100-240V wall charger.
- K-1 Angler Pro Outboard Kit ($1,699): the same motor with the bigger PP-768 pack, which Bixpy says lifts thrust to 38 lb.
- Solar versions ($1,599 and $1,899): each kit also comes bundled with Bixpy’s SUN80 solar panel.
- K-1 motor alone: listed from $749, for people who already have a battery.
No Bixpy trolling motor kit includes a mounting adapter. You buy one separately to suit your kayak, board or boat, and that adapter decides where the motor sits and how you steer.
The N-3 for jon boats and dinghies
The N-3 Outboard Motor and Power Pack Kit ($2,499) is a different machine. It’s a 1.2 kW tiller outboard with a 36V, 1,440 Wh battery and a choice of 22.5 or 27.3 inch shafts. Bixpy lists it for boats from 8 to 14 feet, including jon boats, dinghies, tenders, inflatables and sailboats.
The short shaft system weighs about 44 lb with its bracket and battery. It has a stepless throttle on the tiller and an LCD that shows battery, speed, range and power draw.
Older J-1 and J-2 motors
Bixpy’s site still has a legacy adapter section for its older J-1 and J-2 motors, and some of its image descriptions call the motor the Bixpy Jet. The PP-378 pack runs a J-2. A J-1 needs Bixpy’s Refresh upgrade to work with it. If you’re buying a used setup, find out which motor you’re getting before you order a battery or adapter.
Bixpy trolling motor specs side by side
This is what Bixpy publishes for each setup. The kit pages don’t give a top speed in mph. Bixpy’s motor collection page says the K-1 can push a kayak up to 7 mph, and real speed depends on the hull, the load and the wind.
| Setup | Thrust or power | Battery | Weight | Mounting |
|---|---|---|---|---|
| K-1 motor | 33 lb (PP-378), 38 lb (PP-768) | Bixpy packs, or your own 24V battery (21 to 30 V) through K-Power | 2.8 lb with cable and attachment adapter | Adapter sold separately |
| K-1 Outboard Kit | 33 lb | PP-378, 384 Wh, 25.6 V LiFePO4 | About 11 lb, motor and battery | Adapter sold separately |
| K-1 Angler Pro Outboard Kit | 38 lb | PP-768, 768 Wh, 25.6 V LiFePO4 | 2.8 lb motor plus 21 lb battery | Adapter sold separately |
| N-3 Outboard Motor and Power Pack Kit | 1.2 kW (3 hp equivalent); thrust not listed | NB-1440, 1,440 Wh, 36 V | About 44 lb, short shaft system | Transom bracket, tiller steering |
Bixpy’s pages don’t always agree with each other. The PP-378 shows 384 Wh in its spec list and 378 Wh in its name, and the K-1 kit weight shows as 10 lb on one page and 11 lb on another. We’ve used the figures on the product listings.
The K-1 has 12 forward and 3 reverse speeds on the standard kit, and 13 forward on the Angler Pro. A double press of the remote jumps to full speed, which Bixpy calls Warp Speed. The motor is rated to a depth of 100 ft, and Bixpy says it’s built for fresh and salt water.
How a Bixpy trolling motor mounts
Unlike a clamp-on trolling motor, the K-1 has no clamp of its own. It fits onto an adapter, and Bixpy lists more than 20 of them for specific kayak brands, rudder fittings, fin boxes and transoms. Its product pages say the motor comes off with one bolt, so moving it between boats means buying a second adapter rather than a second motor.
Bixpy has a lookup chart on its site where you pick your boat by make and model. Start there, because many of the adapters are made for specific hulls.
Pedal drive kayaks
Bixpy sells adapters named for pedal drive kayaks from Old Town, Feelfree, Native, BOTE, Hoodoo and Impulse, plus a Mirage Fin Type adapter. The Old Town PDL adapter ($229 list) drops into the pedal well in place of the drive. It fits Sportsman PDL and Topwater PDL kayaks (models 106 and 120), and Bixpy says it fits no other kayaks.
That lets you keep the pedal drive and swap the motor in on days when you need to cover more water. Order by your exact model, not just the brand.
Rudder and stern mounts
The Universal Versa Rudder ($199 list) fits a standard 10 mm rudder pin hole and carries the motor at the stern. Bixpy says the motor has to sit about 2 to 3 inches below the waterline to work well.
Steering comes one of two ways. A V-Arm bracket ties into the kayak’s existing rudder steering lines. For kayaks without steering lines, a telescopic pole handle turns the motor by hand. Other brand-specific options include a Hobie Twist and Stow rudder adapter, a Hobie Lynx gudgeon kit, an Eddyline Versa Rudder, a Bonafide pod adapter and a NuCanoe QuickConnect motor shaft.
Paddleboards, inflatables and transoms
- Fin boxes: adapters for US Fin, Slide and Lock and Flip and Lock boxes, plus a SUP adapter bundle.
- No fin box: glue-on and Peel and Bond fin box adapters add a mounting point. Bixpy lists the glue-on version for inflatables.
- Transoms: a Transom Adapter for boats with a transom.
- Accessory mounts: a Universal Kayak Adapter, a rod holder adapter and a RailBlaza Hexx adapter.
Batteries, runtime and charging
On a Bixpy trolling motor, the battery is a separate pack that sits in the boat. The motor’s 55 inch cable is fixed to the motor and runs to the pack. That keeps the motor light, but it puts most of the weight in the battery. The PP-378 lists at $749 on its own, the same as the K-1 motor’s starting price.
| Spec | PP-378 (V4) | PP-768 (V2) |
|---|---|---|
| Energy | 384 Wh | 768 Wh |
| Voltage and chemistry | 25.6 V LiFePO4, 15 Ah | 25.6 V LiFePO4, 30 Ah |
| Weight | 8 lb | 21 lb |
| In the water | Positive buoyancy | Negatively buoyant |
| Wall charger time | About 5.5 hours | 7 to 8 hours |
| Bixpy runtime claim with the K-1 | About 75 minutes at top speed, up to 10 hours slower | 2+ hours at top speed, up to 24 hours slower |
| List price | $749 | $999 |
Two details matter on a kayak. The PP-378 floats, while Bixpy lists the PP-768 as negatively buoyant, so tether the big pack or keep it inside a hatch. The PP-378 also has an auxiliary outlet with 5V and 12V outputs rated 2.0 A max, with connectors sold separately.
Runtime claims vary between Bixpy’s pages. For the PP-768 we found 20, 22 and 24 hours at slow speed on different pages. The gap between top speed and a slow troll is the useful part. Running flat out drains a pack in roughly 75 minutes to 2 hours. Easing along at low speed stretches it across a day.
Running a K-1 on your own 24V battery
Bixpy’s K-Power Control Module ($179 list) lets the K-1 run from a battery you already own. Bixpy asks for a nominal 24V battery that can supply 15 A or more continuously, inside an operating range of 21 to 30 volts. It recommends lithium-ion or LiFePO4. A single 12V trolling motor battery sits below that range.
Spare packs and solar
Because the pack is separate and sold on its own, a second battery is the plain way to add time on the water. Bixpy’s product pages don’t cover swapping packs while afloat, so plan to do it somewhere stable. With the SUN80 panel, Bixpy quotes 6 to 10 hours of sun to recharge, against about 5.5 hours on the wall charger for a PP-378.
Bixpy vs a 12V transom trolling motor
The usual alternative on a small boat is a hand-steered 12V transom trolling motor and a deep-cycle battery. Minn Kota’s Endura is one example. Its 30 lb model with a 30 inch shaft weighs 19 lb, draws up to 30 A, has 5 forward and 3 reverse speeds, and was $169.99 list on Minn Kota’s site in October 2026.
| Setup | Thrust | Battery energy | Motor plus battery |
|---|---|---|---|
| Bixpy K-1 with PP-378 | 33 lb | 384 Wh | About 11 lb |
| Bixpy K-1 with PP-768 | 38 lb | 768 Wh | About 24 lb |
| Endura 30 with Battle Born 100 Ah lithium | 30 lb | About 1,200 Wh (12 V x 100 Ah) | 50 lb |
| Endura 30 with Odyssey group 31 AGM | 30 lb | About 1,240 Wh rated (12 V x 103 Ah) | 96.8 lb |
Battery weights are from Battle Born (31 lb) and Odyssey (77.8 lb). Thrust figures come from each maker and aren’t measured the same way, so read them as rough. Weight is where a Bixpy and a 12V trolling motor split. A Bixpy kit with the PP-378 weighs about a fifth of the Endura and lithium pair, and roughly a ninth of the Endura with an AGM.
The 12V transom trolling motor wins on stored energy and price. A 100 Ah 12V battery holds about three times what a PP-378 holds. The Endura’s list price is a small fraction of a K-1 kit’s, though you still need a battery. Lead-acid is the cheap way in, but the usual advice is to use only about half its rating if you want it to last.
Our trolling motor battery guide runs through amp-hours and runtime, and the lithium battery guide covers the weight savings in more detail.
Mounting is the other big difference. A transom trolling motor clamps to a flat transom and you steer with a tiller from the back seat. Many kayaks and paddleboards have no transom for a clamp, and that’s the gap Bixpy’s adapters fill. On a jon boat with a proper transom, a regular trolling motor is the simpler choice. Our electric trolling motor guide covers transom and bow mounts side by side.
Who a Bixpy trolling motor suits
- Pedal drive kayak owners: if Bixpy makes an adapter for your drive well, you can switch between pedaling and motoring in the same kayak.
- Anyone who carries the kayak to the water: the motor is 2.8 lb and the small pack is 8 lb, so neither adds much to the carry.
- SUP and inflatable owners: fin box and glue-on adapters give a mount that a clamp-on trolling motor can’t use.
- Salt and fresh water anglers: Bixpy rates the K-1 for both. Rinse it after salt like any other motor.
A Bixpy trolling motor is a weaker fit if you want the motor to hold you on a spot. The K-1 has a Bluetooth remote with set speeds, but Bixpy doesn’t list GPS anchoring, heading hold or a foot pedal throttle. On a bigger boat, a 24V or 36V bow mount with GPS does jobs that a 33 to 38 lb kayak trolling motor can’t. Our bow mount guide covers those.
Check your state’s registration rules before you put any motor on a kayak or paddleboard. Some states treat a kayak with a motor differently from one you paddle.
Adding sonar to a kayak or small boat with a Bixpy
A common question with a kayak trolling motor is how to add a graph. Two things decide it: where the power comes from and where the transducer goes.
Powering a graph
The PP-378’s 12V outlet is rated 2.0 A max. Check your graph’s maximum draw on its spec sheet before you count on that outlet. A Lowrance Elite FS 7 is rated 28 W max, or 2 A at 13.8 V, which is right at the limit. Live sonar needs much more. Garmin rates the GLS 10 module that runs LiveScope Plus at 21 W typical and 58 W max.
For anything past a small graph, give the electronics their own 12V battery and keep the motor’s pack for the trolling motor. Then a flat motor pack won’t leave you without sonar.

Where the transducer goes
Our machined transducer mounts are built for boats with a deck or a rail. None of them is listed for kayaks, so on a kayak you’d use a kayak transducer arm from a kayak accessory maker. We don’t sell those. For the screen, our machined Kayak Single Mount ($351.00) holds one graph and locks into standard kayak track or Yak Attack GridLock track with a knob.
A jon boat or small aluminum boat running an N-3 is different. The Over the Side Mount ($389) bolts to the deck, or sits on our deck plate, a 3 inch track base, a 3/4 to 1 inch round rail mount, or a clamp for 1 1/4 inch square pontoon rail. It puts a live sonar pole anywhere on the boat, with no trolling motor shaft needed.

On that mount, our Handscope ($265) is a hand-aimed pole for Garmin LiveScope and Panoptix, Humminbird MEGA Live and Lowrance ActiveTarget transducers. It comes in 52, 62 and 72 inch lengths. The same mount takes a Live Sweep, and with our MEGA 360 clamp it can carry a Humminbird MEGA 360 too. Our forward-facing sonar guide explains the live views.
What we’d pick for electronics
We’d match the electronics to the boat, not to the trolling motor.
- Kayak or SUP with a K-1: the Lowrance Elite FS 7 with HDI transducer ($864.99). It’s our smallest display and gives you 2D sonar and DownScan Imaging. You’ll still need a kayak transducer arm and a small battery.
- Jon boat with an N-3, traditional sonar: the Elite FS 7 with Active Imaging 3-in-1 ($969.99) adds SideScan, or step up to a 9 inch screen in our graphs section.
- Jon boat with an N-3, live sonar: the Lowrance ActiveTarget 2 System ($1,399.99) on a Handscope and Over the Side Mount. It works with the Elite FS graphs above, and Lowrance lists its maximum current drain at 1.5 A at 13.8 V. Send us your transducer model and we’ll confirm the Handscope fit.
Electronics are final sale in our shop. Check that the graph and transducer work together before you order, and email us if you’re unsure. More poles and bases are in our over-the-side and Handscope mounts.
Gear in this guide

Questions about the Bixpy trolling motor
Is a Bixpy a kayak trolling motor or an outboard?
Bixpy sells the K-1 and N-3 as outboards. On a kayak or paddleboard, the K-1 fills the role of a kayak trolling motor: a quiet electric motor you run at low speed while you fish. The N-3 is a small tiller outboard for boats from 8 to 14 feet.
How much thrust does a Bixpy trolling motor have?
Bixpy rates the K-1 at 33 lb with the PP-378 pack and 38 lb with the PP-768. The N-3 is rated at 1.2 kW, about 3 hp equivalent, and Bixpy doesn’t give a thrust figure for it.
How long does a Bixpy trolling motor battery last?
Bixpy quotes about 75 minutes at top speed for the PP-378 and up to 10 hours at slower speeds. For the PP-768 it quotes 2+ hours at top speed and 20 to 24 hours at slow speed, depending on the page. Wind, current and load all cut those numbers.
Can a Bixpy run on a 12V trolling motor battery?
Not from what Bixpy publishes. The K-Power module needs 21 to 30 volts from a nominal 24V battery that can supply at least 15 A continuously, and Bixpy recommends lithium-ion or LiFePO4.
Does a Bixpy trolling motor have GPS anchoring?
Bixpy doesn’t list GPS anchoring for the K-1 or N-3. If holding a spot hands-free matters to you, read our spot lock trolling motor guide to see how bow mount motors do it.
Do you sell Bixpy?
No. Buy a Bixpy trolling motor, battery or adapter from Bixpy’s site or one of its dealers. We sell the graphs, live sonar and mounts mentioned above.
Need help with sonar for your boat?
Email sales@trollingmotorsdirect.org (Monday to Friday, 9am to 6pm) with your boat or kayak model, where you want the graph and which trolling motor you run, and we’ll help you pick sonar and mounts that fit.








