Skip to content

Garmin · Lowrance · Humminbird trolling motors, live sonar and the mounts to rig them

Mon–Fri, 9am–6pmsales@trollingmotorsdirect.org

Mounts & Parts

Trolling motor mount guide: brackets, stabilizers and sonar mounts

Bolting down the bow bracket, slides and stabilizers, and the mounts that put live sonar or a MEGA 360 on your trolling motor.

12 min read

Trolling motor slide fitted under a Garmin Force Kraken bow mount on a boat deck

A trolling motor mount can mean two different things: the bracket that holds the motor on your bow, or the hardware that holds a sonar transducer on the motor. Both matter, because a loose bracket or a sloppy transducer clamp costs you fishing time and sometimes the part itself.

Each of the four motors we sell comes with its own bow bracket. What we add are the machined parts that go with it: a slide to move the motor back, stabilizers that stop it bouncing, and the brackets that put live sonar or a MEGA 360 on the shaft. Prices below are what you pay in our store today.

Bolting down the trolling motor mount

For most boats, the first trolling motor mount job is bolting the factory bracket down properly. Garmin’s steps for the Force Pro are a good model for any brand:

  1. Choose the spot on the bow. Our bow mount sizing guide covers centerline, overhang and deck access.
  2. Pivot the top of the mount up and back so you can reach the holes in the base.
  3. Lay the paper template down with the bumper over the edge of the deck, pick one of the two port-side hole options to suit your hull, and mark the holes.
  4. Drill the holes with a 5/16 in. (8 mm) bit.
  5. Put the safety strap under the center of the base, hook-and-loop side down, before the base goes on.
  6. Bolt the base down with the supplied bolts, washers and locking nuts, then torque the nuts to 8 lbf-ft (10.85 N-m).

Garmin is firm about the safety strap. Its install manual says it must go under the mount before you bolt it down, or you may have to partly take the motor apart later to fit it. The full steps are in Garmin’s Installing the Mount on the Deck page.

If your deck is too thick for the supplied bolts, Garmin says to use stainless steel pan head 1/4-20 (M6x1) bolts of the right length. Its tool list includes a torque wrench, and it says to use hand tools for the whole job.

Quick-release plates

Some owners want the trolling motor to come off the boat for storage or for winter. That’s what quick-release plates are for. We don’t stock them. If you buy one elsewhere, check that it’s approved for your motor and that the bumper still overhangs the deck once it’s fitted, because a plate under the base changes where the mount sits.

Moving the motor back: the Trolling Motor Slide

A long shaft, a short deck or a big bow overhang can leave the motor hanging well past the front of the boat. The Trolling Motor Slide ($499) is a heavy-duty slide that goes under the trolling motor mount and lets you slide the motor further onto the deck.

  • Travel: it slides 7 inches.
  • Build: marine-grade plastic and black anodized aluminum, with stainless steel hardware. Made in the USA.
  • Fit: it doesn’t currently fit Minn Kota Quest motors. Our product photos show it under a white Garmin Kraken.
Trolling motor mount slide fitted under a white Garmin Kraken
The Trolling Motor Slide fitted under a white Kraken. It moves the motor 7 inches.

Before you order, measure where the bracket sits now and where it would sit 7 inches back. The bumper still has to reach past the gunwale, the motor still has to clear the bow when it deploys, and you need room underneath for the new bolts. Email us your motor and shaft length and we’ll confirm fit.

Stabilizers and rests for a stowed trolling motor

A stowed trolling motor is a long lever sitting on a hinge. Running on plane in a chop or towing on a rough road makes it bounce, and that load goes into the trolling motor mount and the deck.

Garmin’s Force Pro manual lists the stabilizer as an optional accessory that supports the motor when it’s stowed. It also says to fit one to reduce the risk of damage to the mount and the boat in rough conditions or when trailering. Here are the options we stock:

MotorPartOur priceWhat it does
Garmin ForceGarmin Stabilizer for Force (010-12832-50)$119.99Replacement for the stabilizer that shipped with the Force
Garmin Force KrakenGarmin Deck Mount Stabilizer (010-12832-55)$109.99Holds the Kraken shaft when stowed
Lowrance GhostLowrance rod stabilizer kit (000-15278-001)$51.00Lowrance stabilizer rod part for the Ghost
Lowrance Ghost with Live SweepLive Sweep Stabilizer for Ghost$200.00Supports the Live Sweep lower on its tube
Power-Pole ZRPower Pole ZR Bounce Eliminator Kit$99.00Stops the stowed ZR bouncing on the deck
Motors and folding mounts with a kickstandKickstand Rest$20.00Keeps the kickstand off your carpet

Garmin Force and Force Kraken stabilizers

The Garmin Stabilizer for Force is sold as the replacement for the one that came with the Force. If you run a Force Pro, email us before ordering so we can confirm the right part, since Garmin’s Force Pro manual treats the stabilizer as a separate accessory. Garmin’s maintenance list says to check the rubber stops on the stabilizer ends for wear and replace them when needed.

For the Kraken, the Garmin Deck Mount Stabilizer bolts to the deck, and the Kraken owner’s manual says to clamp the shaft in it after you stow the motor. Garmin lists it at 1.45 lb.

Lowrance Ghost stabilizer bar and Live Sweep stabilizer

The Ghost has a stabilizer bar built into its mount, and Lowrance says it cuts bouncing on plane in rough water. Lowrance also sells a rod stabilizer kit for the Ghost (000-15278-001), which we stock at $51.

Ghost owners who add a Live Sweep have extra weight hanging off the shaft. The Live Sweep Stabilizer for Lowrance Ghost ($200) supports the Live Sweep lower on the extension tube and still lets both the motor and the Live Sweep turn. It’s made for Ghost motors mounted with a Cornfield Fishing Gear dog bone, and it comes with a dog bone clamp with marine-grade plastic bushings and two split rings that go on the trolling motor shaft, one each side of the clamp.

Bounce eliminator and kickstand rest

The Power Pole ZR Bounce Eliminator Kit ($99) is black anodized aluminum with stainless hardware, made in the USA. If a bolt won’t go in, the usual cause is powder coat in the Power-Pole holes. Chase them with a 5/16-18 tap.

For carpeted decks, the Kickstand Rest ($20) is a small black anodized aluminum pad that keeps a trolling motor kickstand or folding mount off the carpet. It fastens with one #10 x 1 in. screw, which is included.

Forward facing sonar mounts on the trolling motor

Most anglers fish live sonar from the front deck, so the transducer ends up on or near the trolling motor. There are three ways to hold it there:

  • Clamped to the shaft: the transducer turns with the motor and always looks where the motor points.
  • On a powered arm: the transducer sweeps on its own, so you can look one way while the motor pulls another.
  • On a hand-steered mount: same idea as the powered arm, turned by a knob instead of a pedal.

We stock forward facing sonar mounts for all three. You can browse them in transducer mounts, and our forward facing sonar guide explains the sonar side.

Live View Transducer Mount (shaft clamp)

The Live View Transducer Mount ($333 to $400) clamps to the shaft and holds Garmin LiveScope and Panoptix, Humminbird MEGA Live or Lowrance ActiveTarget transducers. It comes with CNC-machined clamps, an aluminum tube, stainless hardware and a black coiled hose that’s split along its length so you can lay the cable in.

Its fit list includes the Garmin Force, Lowrance Recon, Power-Pole Move PV and a long list of Minn Kota models, in shaft lengths from 36 to 100 inches. The Kraken and Ghost aren’t on that list, so email us if you run one. MEGA Live transducers have molded cable holders that make the hose pucker. Wrap black electrical tape around the hose where they sit.

Live View transducer mount clamped to a trolling motor shaft
The Live View mount holds a live sonar transducer on the shaft, so it turns with the motor.

Live Sweep (powered arm)

Live Sweep is a 12V powered arm that turns the transducer through 320 degrees. You steer it with a foot pedal, wired as standard or wireless for $100 more, and every model comes with a wireless remote fob. The direction arrow doesn’t light up.

  • Live Sweep ($1,099 to $1,199): hardware for the Garmin Force, Lowrance Ghost, Fortrex, Maxxum, Ultrex, MotorGuide Tour 2023 and older, and Power-Pole ZR. It doesn’t fit MotorGuide Xi5 or Xi3 or the Minn Kota Ulterra.
  • Live Sweep for Garmin Kraken ($1,500 to $1,600): 48, 63 or 75 inch shafts.
  • Live Sweep for Lowrance Recon ($1,500 to $1,600): 48, 54, 60 or 72 inch shafts.
  • Live Sweep Garmin Force Mounting Hardware ($297): bracket, bolts and clamps, for moving a Live Sweep you already own onto a Force.

The Garmin and Power-Pole ZR hardware is made for either the port or starboard side, so tell us which when you order. On Lowrance and MotorGuide Tour motors, it mounts with a dog bone. On aluminum deck boats, the Kraken listing recommends the wired pedal.

Cable Steer Live View mount (hand-steered)

The Cable Steer Live View Transducer Mount ($475 to $680) lets you aim the transducer with a twist of a knob. The knob mounts to the gimbal plate of your graph, on the left or right side, and connects to the mount through a 10 ft corrosion-resistant cable. A neon green arrow shows where it’s pointing.

It attaches to the trolling motor, so it stows and deploys with it. Fit options include the Ultrex, Fortrex, Maxxum, Lowrance Ghost, Garmin Force, MotorGuide Tour and Tour Pro (2023 and older) and Power-Pole ZR.

MEGA 360 mounts for the trolling motor

Humminbird’s MEGA 360 scans all the way around the boat, so its trolling motor mount shouldn’t turn every time you steer. Our 360 mounts let it rise and lower with the trolling motor when you stow and deploy, without turning with the steering. The aluminum tube slides through a bushing, so it moves up and down freely.

  • Kraken: the MEGA 360 Mount for the Kraken ($589 to $635) fits 48, 63 and 75 inch Krakens. There’s no version for the 90 inch.
  • Recon: the MEGA 360 Mount for the Recon ($589 to $635) fits 48, 54, 60 and 72 inch shafts.
  • Garmin Force: the MEGA 360 Garmin Force Mounting Hardware ($297) includes a Low Pro 360 mount, a dog bone clamp and stainless hardware, and mounts on either side. The bracket alone is $172.
  • Ghost, Fortrex and Maxxum: the MEGA 360 Clamp ($153) also mounts a 360 off a Handscope or Live Sweep.

The Kraken and Recon mounts are CNC-machined from T6061 aluminum with black powder coat. They clamp to the motor housing above the deck, the tube clamps to the 360 shaft, and no other brackets are needed. Both fit the original 360 and the Fortrex and Ultrex model 360.

Humminbird MEGA 360 on a machined mount attached to a Garmin Kraken
A MEGA 360 on our Kraken mount. It goes up and down with the motor but doesn’t turn when you steer.

If you don’t own the 360 yet, we sell it bundled with the mount. MEGA 360 with the Kraken mount and MEGA 360 with the Recon mount are $1,788.99 each, the same as buying the 360 ($1,199.99) and the mount separately. Both are in bundle deals.

Nose cone transducers: no bracket needed

The simplest trolling motor mount for sonar is none at all. A transducer built into the nose cone has no clamp to slip and no cable on the outside of the shaft.

  • Lowrance Ghost: ships with an HDI nosecone (CHIRP and DownScan). The Active Imaging 3-in-1 nosecone ($392.99) adds SideScan.
  • Lowrance Recon: Lowrance offers an upgradeable sonar nosecone. The Active Imaging 3-in-1 nosecone for the Recon is $359.
  • Garmin Force Pro: the GT56UHD transducer is built in.
  • Garmin Force: the GT Transducer Nose Cone ($99.99) takes GT22, GT24, GT52, GT54 and GT56 transducers.
  • Garmin Force Kraken: the GT56UHD-TR transducer ($474.99) is listed for the Kraken.

Garmin also sells round nose cones in black ($89.99) and white ($119.99) for clamping other gear to the lower unit. Replacement nose cones and transducer kits are covered in our parts guide.

Install tips: Loctite, anti-seize and torque

A machined trolling motor mount takes a lot of vibration. A few cheap habits keep it tight without seizing.

  • Blue Loctite where it must not back out: Garmin’s Force Pro field service manual calls for Loctite 243 on the four threaded holes on top of the propeller drive motor and on the ends of the 1/4-20 shaft cap bolts. Our Blue Loctite ($4) is Loctite 243 in a 0.5 mL capsule, rated for 1/4 to 3/4 in. fasteners and removable when you need it to be.
  • Anti-seize where you’ll want it apart: our anti-seize ($4) is Permatex 09975 in a 4 g pouch. It’s an aluminum, copper and graphite blend that resists salt water and helps stop galling, corrosion and seizing. Use it on stainless bolts going into aluminum clamps that you’ll adjust or remove later.
  • One or the other: don’t put both on the same thread. Decide whether the fastener needs to stay put or come apart.
  • Torque to spec: Garmin’s mount base nuts go to 8 lbf-ft. That’s snug, not cranked, so use a torque wrench rather than feel.
  • Dielectric grease on connections: Garmin’s field service manual calls for it on the power cable and coil cable connections.
  • Check again after a few trips: recheck mount bolts and transducer clamps after the first few runs and trailer trips.

Loctite 243 cures on slightly oily threads, so you don’t need to degrease a used bolt first. Wipe off loose dirt and salt, though.

Which trolling motor mount to buy for your setup

Match your motor and what you want to hang on it to the row below. Prices are ours today.

Your setupWhat to getOur price
Garmin Force, LiveScope turning with the motorLive View Transducer Mount$333 to $400
Recon or Power-Pole Move PV, live sonar turning with the motorLive View Transducer Mount$333 to $400
Garmin Force, live sonar aimed separatelyLive Sweep or Cable Steer$1,099 or $475 and up
Kraken, live sonar aimed separatelyLive Sweep for Garmin Kraken$1,500 and up
Recon, live sonar aimed separatelyLive Sweep for Lowrance Recon$1,500 and up
Ghost with Live SweepLive Sweep plus Live Sweep Stabilizer for Ghost$1,099 plus $200
Kraken or Recon with MEGA 360MEGA 360 mount for that motor$589 and up
Garmin Force with MEGA 360MEGA 360 Garmin Force Mounting Hardware$297
Ghost with MEGA 360MEGA 360 Clamp$153
Kraken bouncing when stowedGarmin Deck Mount Stabilizer$109.99
Motor sits too far off the bowTrolling Motor Slide$499

Gear in this guide

If we had to pick where to start: fit the stabilizer for your motor before anything else, because it protects the bracket you already paid for. Then choose between the forward facing sonar mounts above based on whether the transducer should turn with the trolling motor or on its own. A shaft clamp is cheaper and simpler. Live Sweep costs more but lets you watch a fish while the motor holds the boat on a different heading.

Live Sweep options are in Live Sweep mounts and the 360 hardware is in MEGA 360 mounts. The motors themselves are on our trolling motors page.

Questions about trolling motor mounts

Does a transducer on the trolling motor shaft turn with the motor?

Yes. A shaft clamp like the Live View mount points the transducer wherever the motor points. If you want to look one way while the motor pulls another, you need a Live Sweep, a Cable Steer mount or a separate pole.

Do I need a stabilizer on my trolling motor mount?

If you trailer the boat or run in rough water, yes. Garmin says to fit one in those conditions to reduce the risk of damage to the mount and the boat.

Will the MEGA 360 Kraken mount fit a 90 inch Kraken?

No. It’s made for 48, 63 and 75 inch Krakens only. Email us if you run a longer shaft.

Should I use Loctite or anti-seize on mount bolts?

Use Loctite 243 where Garmin calls for it and anywhere a bolt must not back out. Use anti-seize on stainless bolts in aluminum that you’ll want to remove. Don’t use both on one thread.

Can I move my trolling motor further back on the deck?

Yes. The Trolling Motor Slide moves it 7 inches back. Check that the bumper still overhangs the deck and the motor still clears the bow when it deploys.

Check fit with us first

Not sure which trolling motor mount fits? Email sales@trollingmotorsdirect.org with your motor, shaft length and transducer, Monday to Friday, 9am to 6pm. Electronics are final sale, so it’s worth checking first.

Keep reading

More guides

See all guides

error: Content is protected !!