Skip to content

Garmin · Lowrance · Humminbird trolling motors, live sonar and the mounts to rig them

Mon–Fri, 9am–6pmsales@trollingmotorsdirect.org

Garmin 010-12855-00 Extension

$99.99

Garmin’s 10 ft LiveScope transducer extension cable (010-12855-00). It adds reach between a LiveScope transducer and its sonar module when the stock cable comes up short. Measure your run before ordering.

  • Free ground shipping on orders of $199+ to the lower 48
  • Not sure it fits? Email us before you order
  • Warranty by the manufacturer · Returns
SKU: GAR0101285500
Category: , ,

Description

This is the Garmin LiveScope extension cable 10 ft, Garmin part 010-12855-00. Garmin calls it the LiveScope Transducer Extension Cable, and it does one job: it lengthens the transducer cable so a LiveScope transducer on the trolling motor can reach the sonar module wherever you’ve mounted it. It’s the middle size of the three lengths Garmin makes.

Where the Garmin LiveScope extension cable 10 ft goes

On a typical LiveScope install, the transducer rides on the trolling motor shaft and its cable runs back to the GLS 10 sonar module. Garmin’s LiveScope Plus LVS34 install manual shows the transducer cable plugging into the XDCR port on the module, and it mentions an optional extension cable for runs that need more length. That’s this part.

Common reasons people need it: the sonar module ended up in the console instead of the front compartment, the boat is longer than the last one, or the cable has to follow a rigging tube that adds a few feet of detour.

Pick the length from a real measurement

Run a string or tape along the actual path the cable will take: up the shaft, over the mount, along the deck, through the gunwale or rigging tube, and down to the module. Add slack so the motor can stow, deploy and turn without pulling on anything. Then compare that number with your stock transducer cable. If the shortfall is 10 feet or less, the Garmin LiveScope extension cable 10 ft covers it with a single joint.

LengthGarmin part numberTypical use
3 ft010-13350-01A small gap, or a connection point near the bow
10 ft010-12855-00Module moved farther back, longer deck runs
30 ft010-13350-02Long boats, module at the console or stern

If you land between sizes, go up one rather than stacking two short ones. Every extra joint is one more connector to keep clean and dry. The 3 ft and 30 ft versions are listed separately.

Rigging tips for the extra 10 feet

  • Tape the connector to a pull line before feeding it through a rigging tube, so it doesn’t catch on edges.
  • Keep the joint off the bilge floor and somewhere you can reach it later.
  • Route the transducer cable away from the trolling motor power leads where you can; separating sonar cables from high-current wiring is standard practice for cutting interference.
  • Avoid tight bends and pinch points at the mount hinge. Secure the run with cable ties, snug but not crushing.

Before you order

Garmin’s 010-12855-00 product page doesn’t print a compatibility list, so send us your transducer model if you’re running anything other than a standard LiveScope setup. Like the rest of our electronics, cables are final sale (see returns), which is why we’d rather check first. More LiveScope parts are under Garmin transducers, and our Garmin LiveScope guide covers how the system fits together.

Garmin LiveScope extension cable 10 ft: common questions

Does it carry power or network data?

No. It extends the transducer cable only. Power and network cables for the sonar module are separate.

Do I need it with a new LiveScope system?

Only if the stock transducer cable won’t reach your GLS 10 sonar module. Plenty of installs don’t need one.

Email sales@trollingmotorsdirect.org with your boat length, transducer model and where the module sits, and we’ll help you pick the right length. We’re in Monday to Friday, 9am to 6pm.

Related products

error: Content is protected !!