Skip to content

Garmin · Lowrance · Humminbird trolling motors, live sonar and the mounts to rig them

Mon–Fri, 9am–6pmsales@trollingmotorsdirect.org

Lowrance 83/200/455/800KHZ HDI Transom Mount Transducer 9-Pin Connector 5-Pins Utilized

$138.00

Black Lowrance HDI Skimmer, Medium/High with 455/800 kHz DownScan, part 000-12728-001. 9-pin connector with five pins wired. Includes the skimmer mounting bracket.

  • Free ground shipping on orders of $199+ to the lower 48
  • Not sure it fits? Email us before you order
  • Warranty by the manufacturer · Returns

Description

If the transducer on your transom says 000-12728-001 on the cable, the Lowrance HDI Skimmer 000-12728-001 is its direct match. It’s the black Medium/High HDI skimmer: traditional sonar at 83 and 200 kHz plus DownScan Imaging at 455 and 800 kHz. The plug is 9-pin, but only five of those pins are wired.

Sonar plus DownScan Imaging in one housing

HDI means Hybrid Dual Imaging. Lowrance pairs its broadband sounder with DownScan Imaging inside one transducer, so you get two views from one hole in the transom. Broadband sonar shows fish as arches over a bottom line. DownScan Imaging shows structure below the boat in a picture-like view, which makes it easier to tell a brush pile from a school of fish.

Medium/High describes the sonar side: 83 kHz is the medium frequency with the wider cone, 200 kHz the high one with the tighter, more detailed cone. On DownScan, 455 kHz goes deeper and 800 kHz shows more detail in shallow water.

About the five-pin wiring

A 9-pin Lowrance plug can carry more than an HDI transducer needs, such as SideScan channels. This skimmer only uses five of the nine pins. That’s normal for a sonar and DownScan unit, and the listing calls it out so you can match it to the transducer you’re replacing.

What it means in practice: this is not a SideScan transducer, and an adapter or a different display won’t change that. If you want side imaging, you need an Active Imaging transducer.

What’s in the box

  • Medium/High 9-pin HDI Skimmer (black), part 000-12728-001
  • Skimmer bracket for transom mounting

The parts list for the Lowrance HDI Skimmer 000-12728-001 doesn’t mention screws, so have stainless fasteners and marine sealant on hand for the transom.

Installing the Lowrance HDI Skimmer 000-12728-001

Mount the skimmer bracket where water runs clean across the transducer face at speed, away from strakes, rivets and through-hull fittings. On most outboard boats that means the side where the prop blades travel down. The face should sit at or slightly below the bottom of the hull.

Seal every hole you drill. Route the cable up and over the transom with a drip loop, keep it away from engine and trolling motor wiring, and leave enough slack that a knock to the transducer won’t yank on the plug.

Browse other options in our Lowrance transducers section, or compare it with the HDI skimmer 000-12570-001. For a plain-English primer on sonar, see the fishfinder article on Wikipedia.

Questions

Will it work on my graph?

The Lowrance HDI Skimmer 000-12728-001 needs a Lowrance display with a 9-pin sonar port that supports HDI. Send us your display model and we’ll confirm before you order.

Can I return it if it’s the wrong one?

Electronics are final sale here, so check the part number on your old transducer first. Our returns page has the details.

Email sales@trollingmotorsdirect.org with your boat and display and the number off your old transducer cable, and we’ll match it for you.

Related products

error: Content is protected !!