Skip to content

Garmin · Lowrance · Humminbird trolling motors, live sonar and the mounts to rig them

Mon–Fri, 9am–6pmsales@trollingmotorsdirect.org

Lowrance 83/200/455/800KHZ HDI Transom Mount Transducer 9-PIN

$142.00

Lowrance HDI Skimmer transom mount transducer, 83/200/455/800 kHz, with a 9-pin connector and transom hardware. Gives traditional sonar plus DownScan Imaging on Lowrance units with a 9-pin sonar port.

  • Free ground shipping on orders of $199+ to the lower 48
  • Not sure it fits? Email us before you order
  • Warranty by the manufacturer · Returns

Description

The Lowrance HDI Skimmer 000-12570-001 is a transom mount transducer that runs four frequencies: 83 and 200 kHz for traditional sonar, and 455 and 800 kHz for DownScan Imaging. It ends in a 9-pin connector and comes with transom hardware. Pick it if your Lowrance display has a 9-pin sonar port and you want sonar and down imaging from one housing.

What an HDI transducer does

HDI stands for Hybrid Dual Imaging. It’s Lowrance’s name for a transducer that puts its traditional sonar and DownScan Imaging in one body. The 83 and 200 kHz side draws the familiar 2D sonar with fish arches and a bottom line. The 455 and 800 kHz side draws the picture-like DownScan view of brush, rock and bottom straight below the boat.

As a rule, 83 kHz gives a wider cone and 200 kHz a tighter, more detailed one. On DownScan, 455 kHz reaches deeper and 800 kHz is sharper in shallower water. There’s no SideScan on an HDI transducer. For that, look at Active Imaging.

Lowrance HDI Skimmer 000-12570-001 specs

ItemDetail
Part number000-12570-001
UPC9420024145289
TypeHDI Skimmer, transom mount
Frequencies83 / 200 / 455 / 800 kHz
Connector9-pin
In the boxTransducer and transom hardware

Mounting it on the transom

Where you put a skimmer matters more than anything else in the install. You want clean, unbroken water flowing across the face at speed. Stay away from strakes, ribs and rivet lines, and don’t mount it directly behind anything that throws bubbles.

On an outboard or sterndrive boat, the usual advice is to mount on the side where the prop blades travel downward, to keep it out of the prop wash. Set the face at or just below the bottom of the hull, then seal every screw hole with marine sealant.

Route the cable away from engine wiring and leave a small service loop at the transom. Check the reading at idle, then at cruising speed. If the bottom drops out at speed, the usual fix is a small height or angle adjustment.

Will it plug into your display?

The Lowrance HDI Skimmer 000-12570-001 has a 9-pin plug. Lowrance’s Elite FS displays, for example, list a 9-pin sonar port, and our Elite FS 7 HDI bundle pairs that display with an HDI skimmer. If your unit has an 8-pin port, look at our 8-pin HDI transducer instead. More choices are in our Lowrance transducers section, and the fishfinder overview on Wikipedia explains the basics of how a transducer reads the bottom.

Questions

How is this different from the 000-12728-001?

Both are 83/200/455/800 kHz HDI skimmers with a 9-pin plug. The 000-12728-001 is listed as black, with five of its nine pins wired and its own skimmer bracket. If you’re replacing an old transducer, match the part number printed on its cable.

Does it read water temperature?

The listing for the Lowrance HDI Skimmer 000-12570-001 doesn’t mention a temperature sensor. If temp matters to you, email us before ordering.

Can I return it?

Electronics are final sale at our shop. Read our returns policy and check your connector before you buy.

If you’re unsure about fit, email sales@trollingmotorsdirect.org with your display model and boat, and we’ll confirm the right transducer.

Related products

error: Content is protected !!