Skip to content

Garmin · Lowrance · Humminbird trolling motors, live sonar and the mounts to rig them

Mon–Fri, 9am–6pmsales@trollingmotorsdirect.org

Garmin Transducer Replacement for Kraken

$49.99

Garmin kit (010-12832-26) for replacing or upgrading the built-in transducer on a Force Kraken. Comes with a compression seal wrench, 8-pin and 12-pin seals, an O-ring kit and stainless screws. No transducer or nose cone included.

  • Free ground shipping on orders of $199+ to the lower 48
  • Not sure it fits? Email us before you order
  • Warranty by the manufacturer · Returns

Description

Before you change the transducer in a Garmin Force Kraken, get the Garmin Kraken transducer replacement kit (010-12832-26) on the bench. It holds the seals, O-rings and screws that put the motor back to factory waterproof sealing after you’ve had it apart. There’s no transducer in the box and no nose cone.

Kit contents

ItemWhat it’s for
Compression seal wrenchTightening and loosening the compression seals
8-pin transducer compression sealSealing an 8-pin transducer cable
12-pin transducer compression sealSealing a 12-pin transducer cable
Replacement O-ring kitFresh O-rings for reassembly
Stainless steel screwsNew hardware for the job

Next to the kit for Force motors, this one adds the 8-pin seal, the O-ring kit and the screws. Garmin says to replace all O-rings and compression seals whenever the kit is used. Old seals have already been compressed once, and reusing them is how water finds a way in.

Which Krakens need the Garmin Kraken transducer replacement kit

Garmin builds some Force Kraken motors with the GT56UHD-TR transducer inside and ships others with no transducer. Either way, this kit is for the day the transducer changes: a failed unit, an upgrade, or adding one to a motor that didn’t have it.

If you’re adding a transducer to a Kraken that came without one, the nose cone may need to change as well, and the Garmin Kraken transducer replacement kit doesn’t include one. Our Garmin GT56UHD-TR is listed as Kraken compatible. Email us your Kraken model and the transducer you plan to run, and we’ll put the parts list together.

Working on the Kraken lower unit

The Force Kraken owner’s manual gives the order for getting the nose cone off. Disconnect the battery first and keep every screw in a cup. The nose cone has to come off before any part of the Garmin Kraken transducer replacement kit goes in.

  1. Remove the four skeg screws with a 4 mm hex key.
  2. Remove the screw holding the transducer and nose cone to the bottom of the motor with a 3 mm hex key.
  3. Remove the screws holding the nose cone to the front of the motor with a 4 mm hex key.

With the nose cone off you can reach the front anode. Garmin says to clean it if it’s half its original size or more and replace it if it’s smaller. Motors built after 2024 use two anode screws.

Kraken kit questions

Is a transducer included in the Garmin Kraken transducer replacement kit?

No. It’s seals, O-rings, screws and the wrench. The nose cone isn’t included either.

Can I use the Force kit on a Kraken?

Buy the one made for your motor. The Force kit has no 8-pin seal and no O-ring kit, and our listing names it for Force motors.

Do I need new O-rings if mine look fine?

Use the new ones. Garmin’s advice is to replace all O-rings and compression seals whenever this kit is used, and the O-ring kit is in the box. Like our other Garmin parts, it’s final sale under our returns policy. More Kraken spares are in Garmin trolling motor accessories.

Send your Kraken model, shaft length and transducer plan to sales@trollingmotorsdirect.org and we’ll check every part before you order.

Related products

error: Content is protected !!