Skip to content

Garmin · Lowrance · Humminbird trolling motors, live sonar and the mounts to rig them

Mon–Fri, 9am–6pmsales@trollingmotorsdirect.org

Trolling Motors

Newport trolling motor guide: models, specs and the boats they suit

What Newport lists today, from the 36 lb NV-36 to the NT600 electric outboard, plus thrust sizing, battery math and adding sonar to a small boat.

12 min read

A Newport trolling motor is a transom-mount, hand-steered electric motor from Newport Vessels, and the main line, the NV Series, runs from 36 lb of thrust on 12V to 86 lb on 24V. List prices for those five motors run from $169.99 to $359.99 on Newport’s site in October 2026. Newport also sells long-shaft and kayak versions, plus brushless electric outboards and kayak motors that cost more and run on 24V to 48V batteries.

We don’t sell Newport motors. We sell bow-mount GPS motors, graphs and transducer mounts. The specs below come from the Newport Vessels product pages and the NV Series owner’s manual.

The Newport trolling motor lineup in 2026

Newport splits its motors into three groups on its site: trolling motors, kayak motors and electric outboards. Here’s what each line is.

  • NV Series: The standard transom trolling motor. 36, 46, 55, 62 and 86 lb of thrust, on a 30 or 36 inch shaft.
  • X Series: One 55 lb, 12V model with a 36 inch shaft and a handle that tilts as well as telescopes.
  • L Series: A 40 inch long-shaft motor in 62 lb (12V) or 86 lb (24V), aimed at sailboats and other high transoms.
  • Kayak Series: 36 or 55 lb on a 24 inch height-adjustable shaft, sized for kayaks and canoes.
  • NT300 and NT600: Brushless electric outboards rated at 1,300 W and 3,000 W, on 36V and 48V batteries.
  • NK180 HD and NK300 HD: Brushless kayak motors that bolt on with a four-bolt bracket, on 24V and 36V batteries.

Each NV, X, L and Kayak Series trolling motor has 5 forward and 3 reverse speeds, and Newport lists the NV as a brushed motor. The NT and NK models are a different class. They’re brushless, and they need a separate 24V to 48V battery that isn’t in the box.

Is there a Newport bow-mount motor?

Not on Newport’s own site when we checked in October 2026. None of the Newport Vessels motors listed there is a bow mount. One retailer has posted a listing for a Newport Stance 180 bow-mount kayak motor with GPS anchoring, with the price and release date shown as TBD. Until Newport publishes it, treat those specs as unconfirmed.

Newport transom motors: NV, X, L and Kayak Series

The differences between these four lines are thrust, voltage, shaft length and the handle.

NV Series specs

Newport tags the NV Series as its best seller. It has a 6 inch telescoping tiller. Thrust and amp draw below come from the NV Series owner’s manual. Shaft lengths and prices come from the NV Series product page.

ModelThrust and voltageShaftMax amp drawList price (Oct 2026)
NV-3636 lb, 12V30 in29 A$169.99
NV-4646 lb, 12V30 in40 A$214.99
NV-5555 lb, 12V30 in52 A$239.99
NV-6262 lb, 12V36 in58 A$299.99
NV-8686 lb, 24V36 in48 A$359.99

All five have a 5-point LED battery meter, and the box includes a circuit breaker sized to the model, from 40 A to 60 A. Newport lists weights of about 18 to 25 lb across the range and a 2 year limited warranty.

Look at the NV-86 row. It makes the most thrust in the range but draws fewer amps than the 62, because it runs on 24V. Doubling the voltage cuts the current needed for a given power, which is easier on wire, plugs and terminals.

X Series

The X Series is a single 55 lb, 12V trolling motor with a 36 inch shaft and a 52 A max draw, the same draw as the NV-55. The handle telescopes 6 inches and tilts 30 degrees, and the battery meter is a 10-point LED. Newport lists it at $324.99.

That’s $85 more than an NV-55 for 6 more inches of shaft and the tilting handle. If you sit low in a small boat and a fixed tiller angle is awkward, the tilt is what you’re paying for.

L Series

The L Series puts a 40 inch shaft on the 62 lb (12V) and 86 lb (24V) motors. Newport aims it at sailboats, skiffs and other boats with a high transom, where a 30 or 36 inch shaft won’t get the prop deep enough. List prices start at $324.99.

Kayak Series

The Kayak Series comes in 36 or 55 lb on 12V, with a 24 inch height-adjustable shaft and a built-in battery meter. List prices are $169.99 and $239.99. Newport’s page says it’s designed for quick installation on most kayaks but doesn’t name a mount, so work out how it will attach to your hull before you order.

Newport electric outboards and kayak motors

The NT and NK models are brushless and run on 24V, 36V or 48V. None of them include a battery. Here’s how they compare on Newport’s spec pages.

ModelTypeThrust and powerBattery (not included)List price
NT300Electric outboard110 lb, 1,300 W36V, 30 Ah minimum$1,299.99
NT600Electric outboard160 lb, 3,000 W48V, 70 Ah recommended$2,499.99
NK180 HDKayak motor65 lb, 600 W24V lithium$1,299.99
NK300 HDKayak motor110 lb, 1,300 W36V, 30 Ah minimum$1,499.99

The NT300 comes with a 24.6 inch standard or 29 inch long shaft and weighs 23.8 lb without a battery. Newport pitches it at inflatables, tenders and jon boats.

The NT600 is a heavier unit at 52 lb, with a 26.8 inch shaft, an IP67 rating and an adjustable tiller. Newport says it’s built for boats up to 16 feet, and its FAQ says to expect up to about an hour at full throttle.

The NK180 HD and NK300 HD fix to a kayak with a four-bolt aluminum bracket and steer through a steering triangle. The NK180 HD weighs 14.3 lb and the NK300 HD 25.5 lb. Newport warns that its steering cable kit may not fit every brand of kayak.

Newport quotes top speeds of 6.5 mph for the NT300 and NK300 HD, about 6 mph for the NK180 HD and 10 mph for the NT600. Those are the maker’s numbers. Your speed depends on hull, load and water.

Sizing a Newport trolling motor for your boat

For thrust, the usual guide is about 2 lb for every 100 lb of loaded boat. Loaded means the hull, motor, batteries, fuel, gear and people. Count the people. On a small boat they’re often the biggest part of the load.

Loaded boat weightThrust by the 2 lb ruleSmallest NV that covers it
1,500 lb30 lbNV-36 (36 lb, 12V)
2,000 lb40 lbNV-46 (46 lb, 12V)
2,500 lb50 lbNV-55 (55 lb, 12V)
3,000 lb60 lbNV-62 (62 lb, 12V)
4,000 lb80 lbNV-86 (86 lb, 24V)

That’s the floor for calm water. Wind, current and big water all push the number up, and a transom trolling motor also has to keep the bow from swinging. If you land between two sizes, take the bigger one.

Past about 4,300 lb loaded, the 86 lb motor is at the limit of the rule. A boat that heavy is usually better served by a 24V or 36V bow mount.

Shaft length

Newport’s manual recommends running the motor 6 to 12 inches below the waterline. Measure from where the bracket clamps on the transom down to the water, then add that depth. That’s the shortest shaft that will work.

In Newport’s range, the 30 inch NV shafts suit low transoms on jon boats and small aluminum boats. The 36 inch shafts give you more reach, and the 40 inch L Series is there for sailboats. A shaft that’s too short lets the prop pull air in a chop, and you lose thrust.

Batteries and wiring for a Newport trolling motor

Every Newport trolling motor in the NV, X, L and Kayak Series up to 62 lb runs on one 12V deep cycle battery. The 86 lb models need 24V, which means two 12V batteries in series or a 24V lithium pack. Our 24 volt trolling motor guide shows the series wiring.

We don’t sell batteries. Our trolling motor battery guide covers lead-acid, AGM and lithium, and how to size a bank.

What Newport’s manual says about wiring

  1. Polarity: Red lead to positive, black lead to negative.
  2. Breaker: Fit a manual-reset circuit breaker on the positive lead within 72 inches of the battery. NV and L Series motors ship with one.
  3. Extending the leads: Newport recommends 8 gauge wire if you lengthen the standard cable. The manual has no gauge-by-length table, so keep the extension short.
  4. Plug: A plug lets you unhook the trolling motor without loosening battery terminals. Our trolling motor plug guide covers plug styles and wire sizing.
  5. Lithium: The NV battery meter is set up for 12V deep cycle batteries (24V on the 86 lb). The manual says not to trust it on lithium, so use a separate gauge.

Run time on one battery

Run time is usable amp hours divided by amps. A 100 Ah lead-acid battery used to 50% gives you 50 Ah. At the NV-55’s 52 A max draw, that’s a little under an hour at full speed.

A 100 Ah lithium battery used to about 90% gives roughly 90 Ah, or about an hour and 45 minutes at the same draw. At lower speeds the draw drops a lot and run time goes up. Newport doesn’t publish amps for each speed setting, so time it on your own boat before you count on a full day.

Newport also sells a 12V 50 Ah battery for its motors. Do the math before you pair one with a bigger motor. Even a 50 Ah lithium battery used to 90% lasts about 50 minutes at the NV-55’s full 52 A.

The NT and NK motors are their own case. They need 24V, 36V or 48V batteries sized to Newport’s numbers, such as 36V and at least 30 Ah for the NT300 and NK300 HD.

Which boats a Newport trolling motor suits

  • Jon boats and small aluminum boats: The NV-36 to NV-55 cover loaded weights up to about 2,750 lb by the 2 lb rule, on a 30 inch shaft that fits a low transom.
  • Kayaks and canoes: The Kayak Series for a simple 12V motor, or the NK180 HD and NK300 HD for a bolted-on brushless setup steered by a steering triangle.
  • Sailboats and tenders: The L Series for a high transom. Newport pitches the NT300 at inflatables and tenders.
  • Skiffs up to 16 feet: The NT600, which Newport sizes for skiffs, micro skiffs and dinghies.

A Newport trolling motor makes sense where low cost, low weight and simple controls matter more than GPS or built-in sonar. It’s also an option as the only motor on lakes that don’t allow gas engines.

When a GPS bow-mount makes more sense

A transom motor pushes from the back, and in wind the bow swings off. On a heavier boat, or when you want to fish from the front deck, a bow-mount trolling motor pulls from the front and steers better. GPS bow mounts add anchor lock, so the motor holds you on a spot while you fish.

That’s what we sell, and it’s a big jump in price. The Lowrance Ghost is $3,199.00 and makes 97 lb on 24V or 120 lb on 36V. The Garmin Force Pro is $4,199.99 and carries a scanning sonar transducer in the nose. Both are built for bass boats and bigger hulls. On a 12 foot jon boat on a small lake, an NV Series motor does the job for a small fraction of that.

Adding sonar to a small boat with a Newport

We don’t make transducer mounts for a Newport trolling motor shaft. On a small boat we’d look at two other routes: a graph with a transom transducer, or live sonar on a pole that mounts to the deck or a rail.

A graph with a transom transducer

The Humminbird XPLORE 9 CMSI+ ($1,499.99) comes with the XM 14 HW CMSI T transom transducer. The 9 inch screen fits small consoles and tiller boats where a 10 or 12 inch unit won’t, and you get MEGA Side Imaging+, MEGA Down Imaging+ and CHIRP sonar.

Humminbird XPLORE 9 CMSI+ fish finder with its transom mount transducer
The XPLORE 9 CMSI+ ships with a transom transducer, so it doesn’t need a bow-mount motor.

The Lowrance Elite FS 7 HDI ($864.99) is the cheaper start. Its HDI skimmer shows traditional sonar and DownScan Imaging below the boat, but no SideScan. The display draws about 2 A at 13.8 V, which is tiny next to a trolling motor.

Live sonar on a pole

Live sonar on a small boat doesn’t need a bow-mount trolling motor. Our Handscope ($265) is a machined aluminum pole that holds a Garmin LiveScope or Panoptix, Humminbird MEGA Live or Lowrance ActiveTarget transducer. You aim it by turning the handle. It comes in 52, 62 and 72 inch lengths with a 14 1/2 or 6 inch handle, and it isn’t made to go on a trolling motor.

Over the Side Mount for a live sonar pole, one way to add sonar to a small boat that runs a Newport trolling motor
The Over the Side Mount holds a Handscope or Live Sweep away from the motor.

The pole needs a home. The Over the Side Mount ($389) holds it out over the side, and its base can bolt to the deck or sit on an adapter:

  • Deck plate: A 4 x 4 inch, 1/2 inch thick threaded plate ($51) that stays behind when the mount comes off.
  • Pontoon rail clamp: Fits 1 1/4 inch square rail ($75).
  • Round rail mount: Fits 3/4 to 1 inch round rail ($75).
  • Gunnel rail plate: Fits 1/4 inch track on a gunnel rail ($40).

For a fixed spot that costs less, the Off the Deck Ram Mount ($162.50) holds the Handscope off the deck on a Ram mount with machined brackets.

Pick the pole length by measuring from the mount down to the water, then add enough to get the transducer under the surface. Set the mount where the transducer hangs clear of the hull and the trolling motor.

Handscope live sonar transducer pole with handle
The Handscope takes LiveScope, Panoptix, MEGA Live and ActiveTarget transducers.

For the transducer itself, the Lowrance ActiveTarget 2 System ($1,399.99) is a complete kit: module, transducer on a 25 ft cable, and the power and Ethernet cables. It works with Lowrance Elite FS, HDS PRO and HDS LIVE displays, and the module runs on 12 or 24V.

Electronics are final sale at our store. Check that your graph supports the transducer before you order, or email us and we’ll check it.

Gear in this guide

What we’d pick for a small boat with a Newport

  • To see fish and bottom: The Elite FS 7 HDI at $864.99. Small screen, transom transducer, and room to add ActiveTarget later.
  • For side imaging on a tiller boat: The XPLORE 9 CMSI+ at $1,499.99.
  • For live sonar: The Elite FS 9 with Active Imaging 3-in-1 ($1,119.99), the ActiveTarget 2 System ($1,399.99), a Handscope ($265), an Over the Side Mount ($389) and a deck plate ($51). That’s $3,224.98 before any rail adapter.
  • If you’ve outgrown the transom motor: Our trolling motors are the Garmin Force Pro, Garmin Force Kraken, Lowrance Ghost and Lowrance Recon.

The live sonar setup costs far more than the motor it’s paired with. For a lot of small boats, a good graph with a transom transducer is enough. Orders of $199 or more ship free by ground to the lower 48 and DC; see our shipping policy.

Questions about Newport trolling motors

Is a Newport trolling motor good in saltwater?

Newport lists the NV, X and L Series for saltwater and freshwater, but says the motors are not corrosion-proof. The manual says to rinse with fresh water after every saltwater trip, keep the top cover dry, and use a non-aerosol lubricant on pivot points.

What battery does a Newport trolling motor need?

One 12V deep cycle battery for every model up to 62 lb, and 24V for the 86 lb models. The NT and NK motors need their own 24V, 36V or 48V battery, which isn’t included.

Does Newport Vessels make a bow-mount trolling motor?

Not on Newport Vessels’ own site as of October 2026. A Stance 180 bow-mount kayak motor has appeared in one retailer listing with no price or release date.

Can I run a Newport trolling motor on a lithium battery?

Yes, on the matching voltage. Newport’s manual says the built-in battery meter is designed for deep cycle batteries and can’t be trusted with lithium, so use the battery’s own gauge.

How long will a Newport trolling motor run on one battery?

At full speed, an NV-55 drawing 52 A runs a little under an hour on a 100 Ah lead-acid battery used to 50%. Slower speeds last much longer, but Newport doesn’t publish the draw at each setting.

What warranty do Newport Vessels motors have?

Newport Vessels lists a 2 year limited warranty on the NV, X, L, NT and NK product pages. Its L Series page warns that storing the motor in fresh or salt water could void it.

Ask us about sonar for your boat

Email sales@trollingmotorsdirect.org, Monday to Friday, 9am to 6pm, with your boat, your transom or rail setup and the graph you run. We’ll tell you which sonar and mount fit.

Keep reading

More guides

See all guides

error: Content is protected !!