Skip to content

Garmin · Lowrance · Humminbird trolling motors, live sonar and the mounts to rig them

Mon–Fri, 9am–6pmsales@trollingmotorsdirect.org

Mounts & Parts

Trolling motor parts: what wears out and how to replace it

Props, skegs, nose cones, anodes, remotes and breakers for Garmin and Lowrance motors, with prices, part numbers and how to fit them.

12 min read

Garmin high-efficiency prop for Force trolling motors, model 010-12832-00

Most trolling motor parts that wear out are the cheap ones on the outside of the motor: the prop, the skeg, the nose cone and the sacrificial anodes. After those come the things that get dropped, stepped on or left in the sun, like remotes, pedals, plugs and cables.

Almost all trolling motor parts can be swapped at home with a socket set and hex keys. The prices below are what we charge today, and the steps and torque figures come from Garmin and Lowrance documentation.

The trolling motor parts that wear out first

A trolling motor works hard in places an outboard rarely goes: stumps, rock piles, weed beds and shallow sand. These are the parts that take that abuse:

  • Prop: chipped or bent blades from rocks and stumps, or a sheared drive pin.
  • Prop nut and washers: lost when a prop comes off on the water.
  • Skeg: the fin under the lower unit takes the first hit when you run aground.
  • Nose cone: cracked by a hard impact, or swapped when you change transducers.
  • Anodes: made to corrode so the motor doesn’t, so they wear out by design.
  • Remote or pedal: dropped overboard, stepped on or worn out.
  • Plug, breaker and cables: loose or corroded connections that cut power under load.

None of those means the trolling motor is finished. A new trolling motor prop costs $62 to $99.99 here, and a skeg is $29.99.

Look the lower unit over each time you pull the boat out. A cracked skeg or a prop with a missing chunk is easy to spot on the ramp, and cheaper to fix before it gets worse.

Props, prop nuts and anodes

A trolling motor prop is a wear item. Replace it if a blade is chipped, bent or cracked, if the motor vibrates at speed, or if the drive pin is damaged. Fishing line wrapped behind the prop is the other common problem. Garmin’s Kraken manual lists clearing fishing line and other debris from the prop as part of seasonal maintenance.

Changing a Garmin prop

These are Garmin’s steps from the Force Pro field service manual. The Kraken uses the same socket and torque.

  1. Disconnect the trolling motor from the battery.
  2. Remove the prop nut with a 9/16 in. socket.
  3. Pull the prop off. Keep the lock washer, flat washer and sacrificial anode.
  4. Check that the pin in the motor shaft is in place. Replace it if it’s missing or damaged.
  5. Slide the new prop on.
  6. Refit the anode, then the flat washer, then the lock washer, then the nut.
  7. Tighten the nut to 12 lbf-ft (16.27 N-m).

The order matters. The anode goes against the prop, and the lock washer sits under the nut. If you lose the small hardware on the water, Garmin’s field service manual lists a propeller hardware kit (S00-01000-28) with the nut, washers, shaft pin and anode.

Garmin high-efficiency prop, one of the trolling motor parts that wears first
Garmin’s high-efficiency prop (010-12832-00) is $99.99. The weedless prop is the same price.

Which prop to run

Garmin makes a high-efficiency prop and a weedless prop for its Force motors, and the Force Pro comes with both. The weedless prop is built to push weeds away in heavy vegetation, and the high-efficiency prop is the standard replacement. Keep whichever one you’re not running in the boat as a spare.

On the Lowrance side, the Ghost has its own prop kit (000-15237-001, $62) and the Recon has a 2-blade weedless prop ($64). Lowrance lists the Ghost prop as Ghost only, so don’t try to swap props between the two.

Anodes

Sacrificial anodes corrode so the trolling motor’s metal parts don’t. Garmin says to examine them every season. If an anode is half its original size or larger, take it off and clean it with a wire brush or sandpaper. If it’s smaller than half, replace it.

Garmin motors have one anode on the prop shaft and a second one you reach by taking off the skeg and nose cone. That one is held by a 3 mm screw. The Kraken manual says motors built after 2024 use two screws there, and you should use both when there are two mounting points.

For Lowrance, the Prop Shaft Anode kit (000-15723-001) fits over the existing prop nut. Lowrance makes it for use in salt or brackish water, and its trolling motor page says a freshwater Recon needs the anode prop kit before it goes in salt. We sell it for $27.

Lowrance prop shaft anode kit for Ghost and Recon trolling motors
The Lowrance Prop Shaft Anode (000-15723-001) fits over the prop nut. $27.

Skegs, nose cones and transducers

The skeg and nose cone come off together on a Garmin lower unit. Garmin’s field service manual gives these steps:

  1. Remove the four screws holding the skeg with a 4 mm hex key, then take the skeg off.
  2. Remove the two screws at the front of the nose cone with a 4 mm hex key.
  3. Remove the single screw at the bottom of the nose cone with a 3 mm hex key.
  4. Keep every screw. You’ll reuse them on the new part.

Refit in the reverse order: nose cone on, two front screws, the bottom screw, then the skeg with its four screws. Garmin’s skeg is $29.99 here, in black or white.

Garmin nose cones

There are three to pick from, all listed for Force motors:

  • GT Transducer Nose Cone (010-12832-21, $99.99): takes GT22, GT24, GT52, GT54 and GT56 transducers.
  • Black Round Nose Cone (010-12832-22, $89.99): replaces the standard part or carries clamp-on equipment.
  • White Round Nose Cone (010-12832-23, $119.99): same job, in white.
Garmin GT transducer nose cone for Force trolling motors
The GT Transducer Nose Cone takes Garmin GT22, GT24, GT52, GT54 and GT56 transducers.

Garmin transducer kits

The “Transducer Replacement” items are installation kits, not transducers. You need one when you replace or upgrade the built-in transducer. The kit listing recommends replacing all the O-rings and compression seals so the motor keeps its factory waterproofing.

  • Force kit (010-12832-25, $39.99): compression seal wrench and transducer compression seals, including 12-pin seals.
  • Kraken kit (010-12832-26, $49.99): compression seal wrench, 8-pin and 12-pin compression seals, an O-ring kit and stainless screws. The nose cone isn’t included.

For the Kraken, the GT56UHD-TR transducer ($474.99) is listed as Kraken compatible, with CHIRP from 150 to 240 kHz plus ClearVü and SideVü at 455, 800 and 1000 kHz.

Lowrance nosecones and sonar cables

The Ghost ships with an HDI nosecone. A replacement HDI nosecone is $199, and the Active Imaging 3-in-1 nosecone that adds SideScan is $392.99. The Recon’s Active Imaging 3-in-1 nosecone is $359. Lowrance lists the Ghost nosecone for the Ghost only.

A sonar adapter cable (9-pin mini to 9-pin) also comes in the Ghost box. A replacement is $64. For a separate transducer on a Lowrance setup, we have a 9-pin 83/200 kHz trolling motor transducer with temperature for $95, and a $24 trolling motor adapter listed for the 83/200 HDI transducer.

Remotes, pedals, plugs and breakers

Trolling motor remotes and pedals go missing, get stepped on and get left in the sun. Each brand has its own, and they don’t cross over. Lowrance’s own compatibility list puts the TMR-1 remote with the Ghost and not the Recon, and the Advanced Wireless Foot Pedal with the Recon and not the Ghost.

  • Garmin Handheld Remote (010-12833-00): replacement remote for Force motors, $329.99.
  • Garmin Foot Pedal (010-12834-00): replacement pedal for Force motors, $449.99.
  • Lowrance TMR-1 Remote: GPS remote for the Ghost, with cruise control and LED status indicators, $153.
  • Lowrance FreeSteer Joystick: replacement joystick remote for the Recon, $336.99.
  • Lowrance Advanced Wireless Foot Pedal (000-16177-001): Bluetooth, runs on 3 AA batteries or 12V, with programmable keys, $560.99.
  • Lowrance TMC-1 compass: the Ghost’s trolling motor compass, which comes in the box. A replacement is $163.

Garmin pairs the Force Pro pedal and remote to the motor at the factory. A replacement won’t arrive paired to your motor, so check the owner’s manual for the pairing steps before you head out.

Plugs, breakers and power cables

Garmin specifies a circuit breaker rated for 60 A continuous and at least 42 VDC between the battery and a Force trolling motor. It allows a larger breaker, up to 90 A, in high temperatures or when the circuit is shared, but only after you’ve checked the boat’s wiring. It doesn’t come with the motor. Our Garmin 60A Circuit Breaker is $89.99.

A bulkhead plug lets you disconnect the trolling motor without unbolting cables. Garmin says to use one rated for 60 A or more. Its 70A plug and 70A receptacle for Force motors are $49.99 each. Replace both halves together if the pins are loose or corroded. Our plug wiring post has the install steps.

Parts lists by brand, with prices

Every part below is in our trolling motor accessories section. Part numbers are shown where the maker lists them.

Garmin Force and Force Kraken trolling motor parts

PartFitsOur price
High-efficiency prop (010-12832-00)Force motors$99.99
Weedless prop (010-12832-01)Force motors$99.99
Skeg, black or whiteForce motors$29.99
GT Transducer Nose Cone (010-12832-21)Force motors with GT22 to GT56$99.99
Black Round Nose Cone (010-12832-22)Force motors$89.99
White Round Nose Cone (010-12832-23)Force motors$119.99
Transducer replacement kit (010-12832-25)Force$39.99
Transducer replacement kit (010-12832-26)Force Kraken$49.99
GT56UHD-TR transducerForce Kraken$474.99
60A Circuit BreakerForce motors$89.99
70A Power Plug and 70A Power ReceptacleForce motors$49.99 each
Handheld Remote (010-12833-00)Force motors$329.99
Foot Pedal (010-12834-00)Force motors$449.99

Lowrance Ghost and Recon trolling motor parts

PartFitsOur price
Prop kit (000-15237-001)Ghost$62.00
2-blade weedless propRecon$64.00
Prop shaft anode (000-15723-001)Ghost and Recon, salt or brackish water$27.00
HDI noseconeGhost$199.00
Active Imaging 3-in-1 noseconeGhost$392.99
Active Imaging 3-in-1 noseconeRecon$359.00
Rod stabilizer kit (000-15278-001)Ghost$51.00
TMC-1 compassGhost$163.00
Sonar adapter cable, 9-pin mini to 9-pinGhost$64.00
TMR-1 remoteGhost$153.00
FreeSteer joystickRecon$336.99
Advanced Wireless Foot Pedal (000-16177-001)Select Recon models$560.99

Gear in this guide

How to find the right part number

Ordering the wrong trolling motor parts is the usual way a quick fix turns into a second order. Work through it in this order:

  1. Find your trolling motor’s model number. Garmin’s Force Pro manuals list 010-03011-00 and 010-03011-10. Lowrance numbers its Ghost by shaft length: the 47 inch is 000-14937-001 and the 52 inch is 000-14938-001.
  2. Note the shaft length. Some parts change with it. Garmin’s field service manual lists different upper gas springs and mount rails for the 50 and 57 inch Force Pro.
  3. Look up the part in your trolling motor manual. Garmin accessories use 010- numbers, like 010-12832-01 for the weedless prop. Lowrance uses 000- numbers, like 000-15237-001 for the Ghost prop.
  4. For internal parts, check Garmin’s field service manual. It lists service kits with S00- numbers, such as S00-01000-19 for the mount bumper and S00-01000-76 for the coil cable. We don’t stock those, so ask Garmin for them.
  5. Match it to our SKU. Our SKU is the maker’s number without dashes and with a brand prefix. GAR0101283201 is Garmin 010-12832-01, and LOW00015237001 is Lowrance 000-15237-001.

If you’re not sure, email us the motor model, shaft length and a photo of the old part. That’s the fastest way to get it right.

A simple trolling motor maintenance schedule

Garmin’s Force Pro install manual says routine maintenance before each season is needed to keep the warranty valid. This schedule is built from Garmin’s Force Pro and Kraken manuals. The same habits suit a Ghost or Recon, but check Lowrance’s manual for anything model-specific.

WhenWhat to do
After every salt or brackish tripRinse the whole motor with fresh water and wipe on a water-based silicone spray with a soft cloth. Don’t spray jets of water at the shaft cap.
Before each seasonInspect the power cable and coil cable. Clean the power terminals and tighten the nuts.
Before each seasonLubricate the hinges and bushings, and clean and lubricate the stow and deploy latch.
Before each seasonCheck the mount rails, mount bumper, stabilizer rubber stops, pull cable and handle. Replace anything worn.
Before each seasonExamine the anodes. Clean them if they’re half size or more, replace them if they’re smaller.
Before each seasonClear fishing line and weed from the prop.
After towing on gravel or dirt roadsRepeat the seasonal checks as needed.

Use the lubricant your manual names. For the Kraken hinge, Garmin calls for a non-stick, dry-film lubricant, and for the latch pedal and latch bar it calls for synthetic or marine-grade grease.

Write the date and what you replaced on a strip of tape inside a hatch. It makes the next seasonal check, and any warranty claim, much easier.

Repair or replace

Most trolling motor failures are cheap to fix. Here’s how we’d think about it:

  • Chipped prop, bent skeg, cracked nose cone, worn anode: replace the part. They’re made to be swapped, and the Garmin versions all cost $119.99 or less here.
  • Lost or broken remote or pedal: replace it. Replacements here run from $153 to $560.99.
  • Corroded plug or tripping breaker: replace the plug and receptacle together, and check the wiring before fitting a bigger breaker.
  • Bent or broken shaft: talk to the manufacturer first. Garmin gives the Force Pro and Kraken a lifetime limited warranty on the shaft, and Lowrance gives the Ghost and Recon a lifetime shaft warranty.
  • Steering, GPS or electronics fault inside three years: that’s a warranty claim with Garmin or Lowrance. Both list a three-year warranty on the motor.
  • Electronics fault out of warranty: Garmin’s field service manual covers replacing the circuit board, steering servo and display panel, but that’s service-center work. Get a quote and compare it with a new trolling motor, which runs $3,199.00 to $4,199.99 here.

Garmin also warns that using power tools on a Force Pro trolling motor can damage parts and void the warranty. Use hand tools and a torque wrench for all of the jobs above.

What we’d keep in the boat

The trolling motor parts worth carrying are a spare prop and the tools to fit it. They cover most bad days on the water. For a Force Pro, that’s the second prop that came in the box, and a third weedless or high-efficiency prop is $99.99. For a Kraken, email us before ordering a spare so we match it to your motor. For a Ghost, the Ghost prop kit is $62. Pack a 9/16 in. socket, 3 mm and 4 mm hex keys, and a spare anode if you fish salt.

Unused non-electronic trolling motor parts like props and skegs can come back within 30 days. Electronics such as remotes, pedals and transducers are final sale. Our returns page has the details.

Questions about trolling motor parts

What size socket fits a Garmin trolling motor prop nut?

A 9/16 in. socket. Garmin’s manuals for the Force Pro and Kraken both call for 12 lbf-ft (16.27 N-m) when you tighten it.

How often should I replace trolling motor anodes?

Check them every season. Garmin says to clean an anode that’s still half its original size or more, and replace it once it’s smaller than half.

Do Lowrance Ghost props fit the Recon?

No. Lowrance lists the Ghost prop for the Ghost only. The Recon has its own 2-blade weedless prop, which we sell for $64.

Can I run a freshwater Recon in salt water?

Lowrance says you need the anode prop kit to use a freshwater Recon in salt or brackish water. Its Prop Shaft Anode (000-15723-001) page names both the Ghost and Recon. Email us to confirm it for your motor.

Do you sell Minn Kota trolling motor parts?

No. We don’t sell Minn Kota or MotorGuide motors, or trolling motor parts for them. Minn Kota sells its own parts online. We do stock mounts for some of their motors, including a MEGA 360 bundle with a Terrova mount and Live Sweep hardware for the Fortrex, Maxxum and Ultrex.

Are trolling motor parts from Garmin interchangeable between the Force and Kraken?

Not always. The transducer replacement kits are different (010-12832-25 for the Force, 010-12832-26 for the Kraken), and the props, skeg and nose cones we stock are listed for Force motors. Check the part number against your manual or ask us.

Send us your model number

Email sales@trollingmotorsdirect.org with your motor model, shaft length and a photo of the part, Monday to Friday, 9am to 6pm. We’ll tell you which part to order.

Keep reading

More guides

See all guides

error: Content is protected !!