Skip to content

Garmin · Lowrance · Humminbird trolling motors, live sonar and the mounts to rig them

Mon–Fri, 9am–6pmsales@trollingmotorsdirect.org

Humminbird XP-9-HW Puck Transducer

$139.99

Humminbird in-hull Dual Spectrum CHIRP puck (XP 9 HW, model 710275-1) for HELIX units, including ICE HELIX G2 in open water mode. 2D sonar only, to 1,200 ft. Epoxy kit and 20 ft cable included.

  • Free ground shipping on orders of $199+ to the lower 48
  • Not sure it fits? Email us before you order
  • Warranty by the manufacturer · Returns

Description

For HELIX owners who’d rather not drill the transom, the Humminbird XP 9 HW puck transducer (model 710275-1) is a glue-in Dual Spectrum CHIRP transducer. It bonds inside a single-layer fiberglass hull and sends 2D sonar through it, so you get CHIRP to 1,200 ft without a single hole below the waterline.

HELIX compatibility

UnitWhich models
HELIX 5 CHIRP G2GPS-equipped models only
HELIX 7 CHIRP G2/G3GPS-equipped models and CHIRP DI G2 models
HELIX 7 CHIRP G2N/G3NAll models
HELIX 8 CHIRP G3NAll models
HELIX 9, 10 and 12 CHIRP G2N/G3NAll models
ICE HELIX CHIRP G2All models, in Open Water Mode

SOLIX owners need the XP 14 HW instead.

Sonar specs

  • Dual Spectrum CHIRP: Full 150-220 kHz, Narrow 180-240 kHz, Wide 140-200 kHz
  • Max depth: 1,200 ft (365 m)
  • High frequency beam with a wide cone angle
  • 2D only: imaging HELIX units can use it as a 2D source, but it doesn’t do Side or Down Imaging
  • No temperature sensor; the XP 9 HW T has one

Why pick an in-hull puck

A glue-in puck makes sense when you don’t want more holes in the transom, when the transom is already crowded with brackets, or when the boat sees a lot of trailering and shallow water. With the Humminbird XP 9 HW puck transducer inside the hull, there’s nothing outside to knock out of alignment.

Prep and glue-in steps

A good bond is everything with an in-hull puck. Work through it in this order:

  1. Confirm the hull is single-layer fiberglass at the spot. Cored, foam-filled and aluminum hulls won’t pass the signal properly.
  2. Pick a flat area toward the stern, away from strakes and stringers.
  3. Clean and rough up the surface as the epoxy kit instructs.
  4. Mix the epoxy, press the puck down with a slight twist so air escapes, and leave it alone until fully cured.
  5. Run the 20 ft cable to the HELIX away from power cables.

Done right, the Humminbird XP 9 HW puck transducer keeps reading bottom without anything hanging off the transom.

In the box

An epoxy kit and a 20 ft cable come with the puck.

Questions

Will the Humminbird XP 9 HW puck transducer add side imaging to my HELIX?

No. It’s a 2D CHIRP transducer only.

Can I use it on my ICE HELIX in summer?

Yes, ICE HELIX CHIRP G2 models are listed in Open Water Mode, which suits a boat that doubles as your summer rig.

Can I return it?

No, electronics are final sale here. Our returns policy has the details.

Browse Humminbird transducers, or read the basics of 2D sonar on Wikipedia’s fishfinder page. Send your HELIX model and hull type to sales@trollingmotorsdirect.org and we’ll confirm fit before you order.

Related products

error: Content is protected !!