Skip to content

Garmin · Lowrance · Humminbird trolling motors, live sonar and the mounts to rig them

Mon–Fri, 9am–6pmsales@trollingmotorsdirect.org

Humminbird XP-14-HW Puck Transducer

$149.99

Humminbird in-hull Dual Spectrum CHIRP puck (XP 14 HW, model 710286-1) for SOLIX 10, 12 and 15 G2 units. 2D sonar only, to 1,200 ft. Glues inside single-layer fiberglass hulls; epoxy kit and 20 ft cable included.

  • Free ground shipping on orders of $199+ to the lower 48
  • Not sure it fits? Email us before you order
  • Warranty by the manufacturer · Returns

Description

SOLIX G2 owners with a fiberglass hull can skip the transom bracket with the Humminbird XP 14 HW puck transducer (model 710286-1), an in-hull Dual Spectrum CHIRP transducer for SOLIX 10, 12 and 15 G2 units. It glues to the inside of a single-layer fiberglass hull and shoots 2D sonar through the hull, so there are no holes below the waterline and nothing on the transom to catch weeds or trailer bunks.

What it will and won’t do

  • Dual Spectrum CHIRP 2D sonar: Full 150-220 kHz, Narrow 180-240 kHz, Wide 140-200 kHz
  • Max depth 1,200 ft (365 m)
  • High frequency beam with a wide cone angle
  • No Side Imaging and no Down Imaging; imaging units can use it as a 2D sonar source only
  • No temperature sensor (the XP 14 HW T adds one)

Compatible units

Humminbird lists the Humminbird XP 14 HW puck transducer for SOLIX 10, SOLIX 12 and SOLIX 15, all G2 models. If you run a HELIX, the matching puck is the XP 9 HW. Buy by the unit list, not by how the plug looks.

Why go in-hull

An in-hull puck suits boats that get trailered a lot, run shallow rivers, or already have a crowded transom. Because the Humminbird XP 14 HW puck transducer sits inside the boat, it can’t be knocked off by a stump or a trailer bunk, and there’s no bracket to adjust after a hit.

How in-hull mounting works

An in-hull transducer is bonded to the inside of the hull with epoxy, and the sonar passes through solid fiberglass. That’s why Humminbird specifies single-layer fiberglass: aluminum, cored hulls and hulls with foam or air gaps block or weaken the signal.

  1. Pick a flat spot toward the stern, clear of strakes, stringers and anything that traps air.
  2. Clean and prep the hull surface as the included epoxy kit directs.
  3. Bed the puck so no air bubbles are trapped under it, and let the epoxy cure fully before you run.
  4. Route the 20 ft cable to the console away from power leads.

Expect some signal loss through the hull compared with a transom ducer; that’s the trade for a clean, hole-free install.

In the box

The Humminbird XP 14 HW puck transducer comes with an epoxy kit and a 20 ft cable.

Before you order

Will the Humminbird XP 14 HW puck transducer give me side imaging?

No. It’s a 2D CHIRP in-hull transducer only. An imaging SOLIX can use it, but only as a 2D sonar source.

Can I put it in an aluminum boat?

No. Humminbird lists it for single-layer fiberglass hulls only.

Can I return it?

No. It’s electronics, and those are final sale per our returns policy, so confirm your SOLIX model first.

See all Humminbird transducers, or read how 2D sonar works on Wikipedia’s fishfinder page. Email sales@trollingmotorsdirect.org with your SOLIX model and hull type and we’ll confirm this in-hull transducer will work.

Related products

error: Content is protected !!