Skip to content

Garmin · Lowrance · Humminbird trolling motors, live sonar and the mounts to rig them

Mon–Fri, 9am–6pmsales@trollingmotorsdirect.org

Humminbird XP-9-HW-T Puck Transducer

$149.99

Humminbird in-hull Dual Spectrum CHIRP puck with built-in temperature sensor (XP 9 HW T, model 710276-1) for HELIX 5 through 12 and ICE HELIX G2 in open water. 2D only. Epoxy kit and 20 ft cable included.

  • Free ground shipping on orders of $199+ to the lower 48
  • Not sure it fits? Email us before you order
  • Warranty by the manufacturer · Returns

Description

The Humminbird XP 9 HW T puck transducer (model 710276-1) is an in-hull Dual Spectrum CHIRP transducer with a built-in temperature sensor, made for HELIX fish finders. It glues inside a single-layer fiberglass hull and gives you 2D CHIRP sonar to 1,200 ft and a water temperature readout, with no transom bracket and no holes.

Humminbird XP 9 HW T puck transducer, in-hull CHIRP puck

Which HELIX units it fits

  • HELIX 5 CHIRP G2, GPS-equipped models only
  • HELIX 7 CHIRP G2/G3, GPS-equipped and CHIRP DI G2 models
  • HELIX 7 CHIRP G2N/G3N, all models
  • HELIX 8 CHIRP G3N, all models
  • HELIX 9, 10 and 12 CHIRP G2N/G3N, all models
  • ICE HELIX CHIRP G2, all models in Open Water Mode

For a SOLIX G2, the matching part is the XP 14 HW T.

Why get the temperature version

Water temperature drives where fish set up through the year, so having it on the HELIX screen is handy for deciding how shallow or deep to start. In summer, 2D CHIRP can also show a thermocline as a faint band, and together with the water temperature reading that helps you choose a depth to fish. If you don’t care about temperature, the XP 9 HW is the same puck without the sensor.

Humminbird XP 9 HW T puck transducer specs

  • Dual Spectrum CHIRP: Full 150-220 kHz, Narrow 180-240 kHz, Wide 140-200 kHz
  • Max depth 1,200 ft (365 m); high frequency beam, wide cone angle
  • 2D sonar only; imaging HELIX units can use it as a 2D source
  • Built-in temperature sensor
  • Includes epoxy kit and 20 ft cable

Cable routing

Run the 20 ft cable from the puck forward along existing rigging, up out of the bilge where you can, and away from the bilge pump and power leads. Leave a little slack at the puck so the Humminbird XP 9 HW T puck transducer’s lead never pulls on the epoxy joint.

Where it won’t work

Humminbird specifies single-layer fiberglass. Skip it on aluminum boats, on cored or foam-filled hulls, and anywhere an air gap sits between the puck and the outer skin, because the sonar can’t pass through cleanly. On a suitable hull, glue the Humminbird XP 9 HW T puck transducer to a flat spot toward the stern, clear of strakes and stringers, and follow the epoxy kit directions closely.

Common questions

Is it the same as the XP 9 HW?

Same CHIRP frequencies, depth rating and HELIX list. The T adds the built-in temperature sensor.

Does it support side or down imaging?

No. It’s a 2D CHIRP transducer only.

Will it show water temperature on an ICE HELIX?

ICE HELIX CHIRP G2 models are listed for this puck in Open Water Mode. Send us your model if you want us to double-check the readout.

Electronics are final sale, as our returns policy explains. See all Humminbird transducers. Email sales@trollingmotorsdirect.org with your HELIX model and hull type and we’ll confirm fit.

Related products

error: Content is protected !!