Skip to content

Garmin · Lowrance · Humminbird trolling motors, live sonar and the mounts to rig them

Mon–Fri, 9am–6pmsales@trollingmotorsdirect.org

Humminbird XM-14-HW-CMSI-T Transom Mount Transducer

$449.99

Humminbird Compact MEGA Side Imaging+ transom transducer (model 710311-1) with built-in temperature sensor, 20 ft cable and screw-on connector. Fits APEX, SOLIX G3 and XPLORE units.

  • Free ground shipping on orders of $199+ to the lower 48
  • Not sure it fits? Email us before you order
  • Warranty by the manufacturer · Returns

Description

Packed with our XPLORE CMSI+ kits and sold here on its own, the Humminbird XM 14 HW CMSI T (model 710311-1) is a compact MEGA Side Imaging+ transom mount transducer for APEX, SOLIX G3 and XPLORE units. One ducer covers MEGA Side Imaging+, MEGA Down Imaging+ and Dual Spectrum CHIRP, and it reads water temperature too.

Frequencies and range

ModeFrequencyMax range
Compact MEGA Side Imaging, 455 kHz405-505 kHz800 ft (244 m) side to side
Compact MEGA Side Imaging, MEGA1.100-1.200 MHz400 ft (122 m) side to side
Compact MEGA Down Imaging, 455 kHz420-520 kHz400 ft (122 m) depth
Compact MEGA Down Imaging, MEGA1.125-1.225 MHz400 ft (122 m) depth
Dual Spectrum CHIRPFull 150-220 kHz, Narrow 180-240 kHz, Wide 140-200 kHzNot listed

Humminbird XM 14 HW CMSI T specs

  • Compatible with APEX, SOLIX G3 and XPLORE fish finders
  • Transom mount
  • 20 ft cable with a screw-on connector
  • Built-in temperature sensor
  • 1-year limited warranty

Who it’s for

  • Anyone running a head-only unit such as the Xplore 9 with no transducer who wants a standard transom ducer
  • Owners replacing a damaged XM 14 HW CMSI T after a stump or trailer strike
  • APEX or SOLIX G3 owners who want a compact imaging ducer on a smaller transom

Our APEX kits ship with the XM 14 HW MSI T, a different, non-compact transducer. The Humminbird XM 14 HW CMSI T is the compact version, and it’s also on the APEX compatibility list.

Getting a clean picture from the transom

Side imaging is fussy about water flow. Mount the transducer where water leaves the hull smoothly at speed, away from strakes, rivets, livewell pickups and the prop. Set the angle and height by Humminbird’s instructions, then fine-tune on the water: if the bottom drops out at speed, adjust it a little lower and check again. Seal every screw hole with marine sealant.

Route the 20 ft cable to the console through existing rigging paths and keep it apart from outboard and trolling motor power leads to cut down on interference.

Questions

Will the Humminbird XM 14 HW CMSI T work with my HELIX?

HELIX isn’t on its list. It’s listed for APEX, SOLIX G3 and XPLORE.

Is the 20 ft cable long enough?

Measure from the transom spot to the graph along the real route, including any rise up into the console, before you mount anything. If the run is longer than 20 ft, email us before ordering.

Does it show water temperature?

Yes, it has a built-in temperature sensor.

Transducers count as electronics, so it’s final sale under our returns policy. Browse other Humminbird transducers, read our Humminbird fish finder guide, or see Humminbird’s fish finder lineup. Email sales@trollingmotorsdirect.org with your graph model and boat and we’ll confirm this is the right transom mount transducer.

Related products

error: Content is protected !!