Skip to content

Garmin · Lowrance · Humminbird trolling motors, live sonar and the mounts to rig them

Mon–Fri, 9am–6pmsales@trollingmotorsdirect.org

B&G (Maptech) 170kHz *12 DEGREE TILTED ELEMENT* Depth Transducer Hydra Hercules

$35.99

This 170kHz tilted transducer is an analog depth transducer with a 12-degree tilted element, originally made by Maptech. It runs at 170 kHz, the same frequency B&G uses, so it works with B&G Network-series instruments, Hydra, Hercules and other B&G equipment that uses a 170kHz transducer. It comes with a short whip and a 10-foot extension cable, for a total cable run of about 14 feet. What you get (1) 170kHz tilted element depth transducer (12 degrees) Short whip cable plus a 10-ft extension, about 14 ft in total. Why a 170kHz tilted transducer A 170 kHz analog depth transducer…

  • Free ground shipping on orders of $199+ to the lower 48
  • Not sure it fits? Email us before you order
  • Warranty by the manufacturer · Returns

Description

This 170kHz tilted transducer is an analog depth transducer with a 12-degree tilted element, originally made by Maptech. It runs at 170 kHz, the same frequency B&G uses, so it works with B&G Network-series instruments, Hydra, Hercules and other B&G equipment that uses a 170kHz transducer. It comes with a short whip and a 10-foot extension cable, for a total cable run of about 14 feet.

What you get

  • (1) 170kHz tilted element depth transducer (12 degrees)
  • Short whip cable plus a 10-ft extension, about 14 ft in total.

Why a 170kHz tilted transducer

A 170 kHz analog depth transducer for B&G gear is hard to find now. The tilted element lets the transducer be mounted through a hull with deadrise and still point straight down. This one must be installed where the hull has a deadrise of 8 to 16 degrees, with the “keel arrow” pointing toward the keel. Installed any other way, it won’t read depth properly. B&G instrument manuals on the B&G website show how to connect a depth transducer.

See more single frequency transducers and our clearance section.

Before you install

  • Measure the deadrise where you plan to mount it. It must be 8 to 16 degrees.
  • Point the keel arrow toward the keel.
  • Choose a spot with clean water flow, away from strakes and through-hulls.
  • Bed it with marine sealant suitable below the waterline.
  • Add extension cables if 14 feet won’t reach. We sell extra extensions.

Keeping B&G instruments reading depth

Many sailboats still have B&G Network, Hydra or Hercules systems that work well apart from a failed transducer. Replacing the transducer is far cheaper than replacing the system, and it keeps the depth display on your existing instruments.

170kHz tilted transducer questions

Will it work with my B&G Hydra?

Yes, it’s for B&G gear using a 170kHz transducer.

Can I mount it on a flat hull?

No. It needs 8 to 16 degrees of deadrise.

Buying older marine electronics with confidence

Older and discontinued parts keep a lot of boats running, but fit matters. Before you buy the 170kHz tilted transducer, compare part numbers, connectors and model names with what’s on your boat, and check the photos closely. We list what is included and what isn’t, and we note condition honestly. If you’re unsure whether it will work with your setup, send us your equipment list and we’ll help you check.

Shipping, returns and warranty

Shipping is free to the contiguous United States (lower 48). Hawaii, Alaska, Puerto Rico, other US territories and international orders have shipping calculated at checkout. Every order comes with 30-day returns and a 90-day warranty.

Questions about the 170kHz tilted transducer? Email sales@trollingmotorsdirect.org with your equipment details and we’ll help you check fit before you order.

Additional information

Location

3001300

error: Content is protected !!